FabDigit

Engineering Plastic · Engineering Thermoplastic

PA12-GF

PA12-GF is an engineering polymer — glass-filled sls/mjf nylon. Typical values: 45 MPa yield, 1.22 g/cm³, rated to 110 °C. Available for 3D printing at FabDigit.

3D printingPremium cost $$$
Quote a part in PA12-GFCompare with…All polymer grades

Properties

Typical room-temperature values for the default supply condition. Metric first, imperial in gray. The bars show where PA12-GF sits against the other 74 polymer grades in the catalog.

Datasheet

Yield strength45 MPa7 ksi
Tensile strength51 MPa7 ksi
Hardness110 HRR
Density1.22 g/cm³0.044 lb/in³
Specific strength (yield ÷ density)37
Min service temp-30 °C-22 °F
Max service temp110 °C230 °F
Electrical conductivity< 0.001 % IACSinsulator
MachinabilityVery good80 / 100
WeldabilityFair50 / 100
FormabilityPoor30 / 100

Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.

Against other polymer grades

Yield strength45 MPa 7 ksi
5 MPafamily median 50 MPa89 MPa
Tensile strength51 MPa 7 ksi
11 MPafamily median 55 MPa95 MPa
Density1.22 g/cm³ 0.044 lb/in³
0.97 g/cm³family median 1.2 g/cm³1.59 g/cm³
Hardness (HB equiv.)—
Max service temp110 °C 230 °F
72 °Cfamily median 100 °C257 °C
Electrical conductivity< 0.001 % IACS insulator
< 0.001 % IACSfamily median < 0.001 % IACS< 0.001 % IACS
Machinability80 / 100
20 / 100family median 70 / 10085 / 100
Relative cost26
14family median 2899

Strength versus weight in the polymer family

Yield strength against density for every polymer grade FabDigit runs. PA12-GF is highlighted; hover a dot for its name, or open the interactive family chart.

1101000.511.52Density (g/cm³)Yield strength (MPa) — log scaleABSHDPELDPEPA11PA12PA12-CFPLA-CFPETG-CFABS-ESDPC-FRPC-ISOPEKK-ESDPA6PA66PC-ABSPOM-CPOM-HPPPVCUHMW-PEPETGPCFEPPIPBIPCTFEPEEKPEKKPFAPPSPPSUPSUPTFEPVDFPAIPEIASAEPDMLCPPBTPETPMMASiliconeTPETPUCPVCPOMPA6GPPAMXD6FKMFFKMNBRPU CastPU FoamEPP FoamPoronEVA FoamPLAStandard ResinTough ResinRigid ResinFlexible ResinVeroPX223PX521AgilusDigital ABSClear ResinDurable ResinHigh Temp ResinDental ResinAlumidePA12-GF

Manufacturability

The process limits FabDigit's quote engine applies to PA12-GF. Design inside these and the part quotes instantly; outside them it routes to an engineer.

3D printing

TechnologiesSLS, MJF
Layer height50 – 300 µmdefault 100 µm
Minimum wall / feature1 / 0.5 mm
Build envelope300 × 300 × 380 mm
SupportsYes
AnisotropyModerate

Surface finishes for PA12-GF

Coatings and treatments compatible with polymer on the processes PA12-GF runs on. Pick them in the quote configurator or call them out on the drawing.

Coating

  • Clear Coating
  • Conductive Coating
  • EMI Shielding Coating
  • Primer Coating
  • Soft Touch Coating
  • Tinted Coating
  • UV Coating
  • Waterproof Coating

Coloring

  • Dyeing (Nylon)
  • Painting

Metallization / Functional

  • Vacuum Metallization

Equivalent designations

Standards and trade names that resolve to PA12-GF in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.

GB (China)
HP PA12PA12
Also called
Glass Filled NylonGlass Bead NylonGlass Fiber Nylon
Other
PA 3200 GFPA12 GFPA3200GFPA12-GBPA 12 Glass FilledGlass Filled Nylon (PA12 GF)PA12 Glass Bead

Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.